Timecounter "HPET" frequency 14318180 Hz quality 950Įvent timer "HPET" frequency 14318180 Hz quality 450Įvent timer "HPET1" frequency 14318180 Hz quality 440Įvent timer "HPET2" frequency 14318180 Hz quality 440Įvent timer "RTC" frequency 32768 Hz quality 0Īttimer0: port 0x40-0x43,0x50-0x53 irq 0 on acpi0 WARNING: VIMAGE (virtualized network stack) is a highly experimental feature.ĪCPI Warning: FADT (revision 5) is longer than ACPI 5.0 version, truncating length 268 to 256 (20111123/tbfadt-325) ![]() TSC: P-state invariant, performance statisticsįreeBSD/SMP: Multiprocessor System Detected: 8 CPUs Origin = "GenuineIntel" Id = 0x406d8 Family = 0圆 Model = 0x4d Stepping = 8 All rights reserved.įreeBSD is a registered trademark of The FreeBSD Foundation.įreeBSD 9.3-RELEASE-p13 #4 r281084+c7bb047: Wed Apr 15 15:03:01 PDT amd64 The Regents of the University of California. It takes way longer then that to boot though. As if it had booted just when I started testing. When I went to check uptime, it said 1 min. ![]() When I went to check if it was running, at first I was not able to connect, but a few seconds after, I connected. It acted kind of weird when I got up and tested it today though. However, since replacing the boot drive it now correctly reboots and no longer targets a storage-drive when booting. Got the same "security run output" message at 03.01 as before. I was able to reproduce the issue tonight. Could it be my powersupply is not able to handle the load of the systemscripts running? Seasonic Sea Sonic G Series 360 360watt 80 PLUS Gold.2x ECC RAM Kingston DDR3 1600MHz 8GB ECC KVR16E11/8.I am running a asrock C2750D4i with a Intel Avoton C2750 Octa-Core Processor:.So thank you for taking the time to answer. I am quite new to this, so any help and guidance is greatly appreciated. I will try to extract all the information I can. > vboxdrv: fAsync=0 offMin=0x570 offMax=0x15a8 > Timecounter "TSC-low" frequency 1200029052 Hz quality 1000 da0 at umass-sim0 bus 0 scbus17 target 0 lun 0 Had the same reboot today with this message: (I had sabnzbd and sickbeard installed previously, removed them now as I no longer had any use for them)įreenas.local changes in mounted filesystems: Weird thing, after replacing the boot drive, things seem to boot correctly. > epair1b: Ethernet address: 02:5b:85:00:09:0bĭoes that give any clue as to what is wrong? > vboxdrv: fAsync=0 offMin=0x5d0 offMax=0x1818 ![]() > Timecounter "TSC-low" frequency 1200029124 Hz quality 1000 > da0: Removable Direct Access SCSI-0 device > ada0: ATA-9da0 at umass-sim0 bus 0 scbus17 target 0 lun 0 > umass0: SCSI over Bulk-Only quirks = 0xc100 The latest information I have gotten is this: This have started happending after the latest update. It seems to work fine all day, but at 03:00 ish, it shuts off. I then have to reboot and change boot order. Since the last update, I have been having the problem that my server restarts at night, and tries to boot from the storage drive.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |